coswick.com
Coswick. Inspire
0
Product was added to your cart
www.coswick.ru
RU
  • HOME
  • PRODUCTS
    • PLANK HARDWOOD FLOORING
    • MOSAIC WOOD FLOORING
    • SPORTS FLOORING
    • WALL PANELS
    • MOLDINGS
    • ACCESSORIES
    • CARE PRODUCTS
  • CHOOSE YOUR COLOR
  • WHY COSWICK
  • ABOUT US
  • WHERE TO BUY

3-LAYER T&G ENGINEERED FLOORING Thickness 19.05 mm

Home TECHNICAL INFORMATION TECHNOLOGIES 3-LAYER T&G ENGINEERED FLOORING Thickness 19.05 mm

FEATURES OF CONSTRUCTION

Perfectly balanced symmetrical design with improved stability maintains its dimensions in an extended range of ambience humidity.

Only hardwoods. All three layers are made of hardwood: the top layer is oak, ash or American walnut, the middle layer is birch, and the bottom layer is oak or birch.

Using birch as a middle layer instead of softer softwoods increases the stability of the floorboard, as birch is much more resistant to warping.

Increased thickness of the middle layer. The middle layer is the most important structural element. It takes on the main load, balancing the deforming effect of the thinner upper and lower layers. Accordingly, increasing the thickness of the middle layer improves the stability of the board. This is especially true for wide plank formats – 190 mm or more.

Dimensional symmetry. The upper and lower lamellas have the same thickness of 3.2 mm, so they act symmetrically on the middle layer when environmental conditions change, the loads arising in them balance each other. This increases the balance of the structure and virtually eliminates the possibility of parquet planks warping.

For the top layer, a sawn lamella is used, which eliminates the presence of internal cracks in it. The texture of the sawn lamella does not differ from the texture of the massive floor board.

Cork expansion joints in the middle layer reduce the internal stresses of the wood during humidity fluctuations, providing additional stability to the parquet board.

Super strong connection of lamellas. To connect the lamellas, a special polyurethane hot melt adhesive is used. It is very durable, moisture resistant and elastic. Therefore, the connection retains its properties throughout the entire service life: there is no “aging” effect, the parquet board does not delaminate along the glue line.

Strong and reliable traditional tongue-and-groove connection. Thanks to the ideal geometry and the use of birch wood in the middle layer, the contacting surfaces do not have chips and do not crumple, the appearance of squeaks during operation is excluded.

Environmentally friendly. All auxiliary materials used in the production process are selected taking into account strict requirements for environmental safety. In the finished product, there is no emission of formaldehyde and other substances harmful to human health.

The reliability and durability of the structure is confirmed by a lifetime warranty on the structural integrity of parquet planks.

INSTALLATION

  • A three-layer board with tongue and groove connection can be installed in rooms above, at or below ground level.
  • Can be installed on top of underfloor heating systems.
  • It can be installed in rooms with increased loads.
  • Installation method – rigid fixation: directly on a concrete base with glue or on a wooden (plywood) base with brackets.

Read more

mm
inch
mm
Dimensions of 3-layer T&G engineered flooring
Thickness, mm 19.05 19.05 19.05 19.05
Top lamella thickness, mm 3.2 3.2 3.2 3.2
Width, mm 127 190 240 300
Length, mm 600…2100 600…2100 600…2100 2950
Microbevel, mm 0.5 0.5 0.5 1.0
Average length, m 1.0 1.22 1.31 2.95
Quantity per pack, m2 2.0 1.86 1.88 1.77
inch
Dimensions of 3-layer T&G engineered flooring
Thickness ¾” ¾” ¾” ¾”
Top lamella thickness 3.2 mm 3.2 mm 3.2 mm 3.2 mm
Width 5″ 7 ½” 9 1/2″ 11 13/16″
Length 2’…7′ 2’…7′ 2’…7′ 9 11/16′
Microbevel 0.5 mm 0.5 mm 0.5 mm 1 mm
Average length, 3 5⁄16′ 4′ 4 5/16′ 9 11/16′
Quantity per pack 21.52 sq.ft. 20.01 sq.ft. 20.23 sq.ft. 19.05 sq.ft.

SEE ALSO:

  • EXPERT ADVICE / BLOG
    • BUYING WOOD FLOORS
    • INTERVIEWS
    • RENOVATION
    • TIPS AND ADVICE
  • WHERE TO BUY?
  • GO TO COLOR SELECTION

TECHNICAL INFORMATION

  • TECHNOLOGIES
    • 3-LAYER T&G ENGINEERED FLOORING Thickness 19.05 mm
    • 3-LAYER T&G ENGINEERED FLOORING Thickness 15 mm
    • 3-LAYER SINGLE STRIP FLOORING COSLOC 5G
  • FINISHING SYSTEMS
    • SILK FINISH
    • SILK MATT FINISH
    • LACQUER FINISH
  • WOOD SPECIES
  • GRADES
    • OAK
    • ASH
    • AMERICAN WALNUT
  • CERTIFICATES
  • WARRANTIES
  • HARDWOOD FLOORING INSTALLATION
    • INSTALLING SOLID WOOD FLOORING
    • INSTALLING SINGLE STRIP FLOORING COSLOC 5G
  • HARDWOOD FLOOR CARE
  • DOWNLOAD
About Us
Contacts
Dealer Login
Recent News
Sitemap

Follow us

Email
Facebook
Twitter
LinkedIn
YouTube
Vimeo
Instagram
Pinterest
Houzz
Viber
RSS

Certificates

nwfa_logo ce_logo ISO 9001leed-logo mas_logo

Contacts

2B Kolasa Str Zaslavl,
Republic of Belarus 223 034
+375-17-543-2012
+375-17-543-2020
mail@coswick.com
© Coswick Ltd. 2008-2023 All rights reserved | Privacy Statement | Terms Of Use